Socket Od Chart
Socket od chart
What is the size chart for sockets?
3/8″ Drive | 1/4″ Drive | 1/2″ Drive |
---|---|---|
6mm | 4.5mm | 9mm |
7mm | 5mm | 10mm |
8mm | 5.5mm | 11mm |
9mm | 6mm | 12mm |
What is the OD of a 1/2 socket?
Item # | Diameter | Tip Outside Diameter |
---|---|---|
1882336 | 7/16" | 25/32" / 18mm |
1882337 | 1/2" | 51/64" / 20mm |
1882338 | 9/16" | 7/8" / 22mm |
1882339 | 5/8" | 61/64" / 24mm |
What is a socket diameter?
There are four common socket sizes: 1/4 inch (0.6 centimeters), 3/8 inch (0.9 centimeters), 1/2 inch (1.3 centimeters) and 3/4 inch (1.9 centimeters). In-between sizes are available too, starting with 1/4 inch (0.6 centimeters) and increasing every sixteenth of an inch (0.16 centimeters).
What is the OD of a 3/8 socket?
The size of the drive hole is determined by usage and torque demand. Common measurements are as follows: 1/4”(6.3mm), 3/8”(9.5mm), 1/2”(12.7mm), 3/4”(19.0mm) and 1”(25.4mm)。 Why use inch?
Are 3/4 and 19mm the same?
19mm = 3/4 inch. 20mm = 25/32 inch. 21mm = just over 13/16 inch. 22mm = almost 7/8 inch.
What are the 3 types of sockets?
Three types of sockets are supported:
- Stream sockets allow processes to communicate using TCP. A stream socket provides bidirectional, reliable, sequenced, and unduplicated flow of data with no record boundaries.
- Datagram sockets allow processes to use UDP to communicate. ...
- Raw sockets provide access to ICMP.
Are sockets measured in diameter?
Socket sizes are measured based on imperial system inches and fractions. Some of the commonly used SAE sizes are 3/8 in., 5/8 in., and 11/16 in. sockets. Metric sockets: Ideal for working on imported vehicles, metric sockets' sizes are measured in millimeters.
Whats better 6 or 12 point sockets?
Answer: It's true that 12-point sockets are fine for most lightweight repairs, but heavy wrenching calls for a six-point socket. A six-point socket is much less likely to slip off a stubborn fastener or round over the corners. Here's why: (1) Six-point sockets have thicker walls, so they're less likely to flew.
What is the OD of 1 4?
1-1/4 Inch diameter Clear 40 PVC pipe (Schedule 40), Cut to Length. PVC pipe is measured by the nominal inside-diameter (ID), not the outside-diameter (OD). Pipe has an approximate ID of 1.360 inch and an approximate OD of 1.660 inch, per PVC Schedule 40 Specifications.
What is the OD of a 1/2 NPT fitting?
Nominal Pipe Size | Outside Diameter of Pipe | Wrench Makeup Length for Internal Thread |
---|---|---|
1/8 | 0.405 | 0.1111 |
1/4 | 0.540 | 0.1667 |
3/8 | 0.675 | 0.1667 |
1/2 | 0.840 | 0.2143 |
What is the OD of 1/2 black pipe?
Item # | Size | Outside Diameter |
---|---|---|
SCH 40 Pipe-1/2 | 1/2 in | 0.840 in |
SCH 40 Pipe-3/4 | 3/4 in | 1.050 in |
SCH 40 Pipe-1 | 1 in | 1.315 in |
SCH 40 Pipe-1 1/4 | 1 1/4 in | 1.660 in |
What are the 3 socket sizes?
Socket Drive Sizes Metric and Standard (SAE) sockets come in three available drive sizes: 1/4 inch, 3/8 inch, and 1/2 inch. The measurement refers to the size of the square used to attach the to socket to a wrench or a ratchet.
What are the 3 common sizes of ratchets?
Available with different drive sizes — 1/4 inch, 1/2 inch and 3/8 inch — to operate different size sockets. Most operate with a geared drive; those with a higher tooth count let you operate the tool with a smaller swinging motion, which is useful when there's little room to move the handle.
What size is a 10 mm socket?
The equivalent imperial size of a 10mm socket is a 3/8 socket. Imperial sizes are known as SAE (Society of Automotive Engineers) or Standard.
What size is 3/8 OD?
Standard Nipples and Pipe Sizing | ||
---|---|---|
Pipe Size | Outside Diameter (O.D.) Fraction Inch (quick reference only) | Outside Diameter (O.D.) Actual - inches |
1/4" | 35/64 | 0.540" |
3/8" | 43/64 | 0.675" |
1/2" | 27/32 | 0.840" |
What sizes are in a 3/8 socket set?
3/8 Inch Square Drive: Six Point Standard Sockets (5/16, 11/32, 3/8, 7/16, 1/2, 9/16, 5/8, 11/16, 3/4, 13/16) Six Point Metric Sockets (8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21) Six Point Metric Deep Sockets (8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19)
How many mm is a 3/8 socket?
SAE | Metric | Inch |
---|---|---|
3/8" | 0.375 | |
10mm | 0.394 | |
13/32" | 0.406 | |
11mm | 0.433 |
Can I use a 3/4 socket instead of a 19mm?
No, there's no need to get a 19mm socket, and it will present no difference in performance just because the number on the side is different.
What's the same as 3 4 in metric?
BOLT DIAMETER | STANDARD | METRIC |
---|---|---|
1/2" | 3/4" | 19mm |
9/16" | 13/16" | 21mm |
- | 7/8" | 22mm |
5/8" | 15/16" | 24mm |
Post a Comment for "Socket Od Chart"